Posts

LABORATORY 3 OF MEDICAL INSTRUMENTATION

Image
Salam & Greetings ! This is the last laboratory session which is laboratory 3. It is a continuation of previous lab 2.  Student need to complete all the task given based on the labsheet.  Below are the list of components used in order to conduct the laboratory experiment : TASK 3.1 : Signal Conditioning Output or Vout on DAQ  Task 3.1 Block Diagram on LabVIEW Vout Signal TASK 3.2 : Testing DAQ on NI MAX Testing the DAQ on NI MAX is important to ensure the DAQ works properly and accordingly. TASK 3.3 : Filtered and Unfiltered Signal Task 3.3 Block Diagram Unfiltered and Filtered Signal TASK 3.4 :  l  Describe the filtered signal (Vout) conditioning, in terms of; i). Signal to Noise Ratio (SNR) ii). Amplification  Task 3.4 Block Diagram Output signal TASK 3.5 :   S ignal ...
Post a Comment
Read more

EXERCISE 3

Image
Salam & Greetings ! This is the exercise 3 of medical instrumentation from vle.unikl. Student are required to complete these tasks. Calculation for the tasks Block diagram and output signal for question 1 ( Additional function 1kHz ) Block diagram and output signal for question 2 ( Multiplication function ) Block diagram and output signal for question 3 ( Subtraction function ) Thank you !
Post a Comment
Read more

EXERCISE 1

Image
Salam & Greetings ! This is the exercise 1 from vle.unikl. Student are required to complete these exercise. Triangle wave with 3.5 V p-p. Block diagram for triangle waveform Triangle waveform signal Knob was used to trim the offset of the signal. Square wave with 2.15 Vamp Used the analogue trainer to change the output waveform into square wave. Sinusoidal with 4.75 Vrms Block diagram Sinusoidal waveform with 4.75 Vrms Used analogue trainer to change the pattern of wave into sinusoidal waveform. Thank you ! 
Post a Comment
Read more

LABORATORY 2 OF MEDICAL INSTRUMENTATION

Image
Salam & Greetings ! This is the Laboratory 2 of medical instrumentation. It is a continuation from previous lab so the same circuit was used. Below are the components used for this lab. Below are the task student need to complete.  Student are required to select a best option of optic sensor based on the application that has been assigned to each group. For my group, we prefer to use photodiode in order to measure the level  of liquid or water. Amplification Unit Student required to amplify the signal of circuit from previous lab based on gain given. This means the circuit prom previous lab will be our input signal for amplifier. As the input signal in positive value, we choose to use non - inverting amplifier in order to get 10 as value of the gain.  This is the calculation used to get the value of resistor in order to get 10 as value of the gain. So we used 18kOhms as R1 and 2kOhms as R2. ...
Post a Comment
Read more

PBL DISCUSSION

Image
Salam & Greetings ! This is the assignment of Problem Based Learning ( PBL ) of medical instrumentation. Below are the PBL assignment. Based on the problem statement above, student need to form a group of 6 in order to proceed with this assignment. Student required to appoint the roles for each member. These are the members of our group and their role.  Aziez  ⇛  Chairman Aiman    ⇛ Team Leader Firdaus      ⇛  Team Member Syafiq        ⇛  Team Member Amir          ⇛  Team Member Hafriz Yazin        ⇛  Cameraman & Editor Then, student need to brainstorm and discuss as a team in order to solve the problem statement.  Brainstorming and Discussion Session Presentation Session  The procedure and event of this PBL assignment ...
Post a Comment
Read more